SIMATIC NET communication card for laptop,correspond to Siemens 6GK1551-2AA00,optoelectronic isolated,anti-lightning and surging,suitable for laptop PCMCIA 32bit CardBus slot,is used to achieve PROFIBUS/MPI/PPI/FWL communication connection between PC and SIMATIC,communication speed is 9.6Kbps~12Mbps.After switched over by the transition card,it can be used for desk computer and secondary generation ExpressCard slot laptop.CP5512 +(PCI->PCMCIA) transition card,then can be used for desk computer; CP5512 + (PCMCIA(II)->PCMCIA)transition card,then can be used for secondary generation ExpressCard slot laptop. If you want to directly buy the CP5512 expresscard,please click this link to get: CP5512-Express Not made by Siemens,OEM product Not including MPI extension cable for card communication,if you also need this,please also order it: MPI Cable Introduction: CP5512 is the isolated PROFIBUS/MPI/PPI/FWL communication card specially for laptop, use iCoupler isolators eliminate optocoupler limitations instead of Photoelectric isolation,with small  dimension, wide temperature range,and have anti-lightning and surging protective circuit and Overcurrent protection with  restoration function on the RS485 interface, all use industrial IC in order to apply to wider temperature range, is used to achieve PROFIBUS/MPI/PPI/FWL communication connection between laptop and SIMATIC. CP5512 insert laptop PCMCIA slot from outside. Its function and Features is the same as Siemens original CP5512(Siemens part nr 6GK1551-2AA00 ),and have the following new characters. 1. Card and RS485 adapter integrative design, small dimension, use conveniently and  have anti-lightning and surging protective circuit on the RS485 interface. 2.Support hot plug, you can plug or unplug the card when the laptop is running. And card and adapter is integrated, so it’s not like original CP5512 which exist the hidden trouble that destroy the card when plug or unplug the card from the adapter with current. 3.Support common Express to PCMCIA transition card. You can use it on the Express slot laptop. 4.Support common PCI to PCMCIA transition card. You can use it on the desk  computer and the function is the same as Siemens original CP5611 and CP5611 A2. Communication service: PROFIBUS-DP master station class 1 and 2 PROFIBUS-DP slave with SOFTNET-DP slave MPI/PPI/FWL communication S7 communication with SOFTNET-S7 S5-compatible communication (SEND/RECEIVE based on the FDL interface) with SOFTNET-DP or SOFTNET-S7 CP5512 can be used with:  STEP7  V5.2 SOFTNET-S7  V6.1 SOFTNET-DP, SOFTNET-DP slave from V6.1 STEP 7-Micro/WIN from V3.2 SP4 ProTool®, ProTool/Pro® V6.0 SP2 NCM PC from V5.2 SIMATIC PDM V5.2 SP1 Technical Specification: Transmission rate: 9.6Kbps～12Mbps,the corresponding largest communication distance accord with PROFIBUS standard. Interface:connect PROFIBUS/MPI/PPI,isolated 9 pin Sub-D connector. Isolated voltage:1000VDC Interface protection:have anti-lightning and surging protection(Ipp=100A 10/700us,4KV) on the RS485 interface.ITU-TK20/21,VDE 0433 standard. ±15KV ESD protection. Overcurrent protection with  restoration function：RS485 port can withstand up to 60V voltage caused by continuous over-current. Standard working voltage:3.3 VDC power：1.0W  working temperature：-20～+75℃  size：length* width * height(mm)：130×54×5（DB9F plug height:22mm）  weight：70g     Support hardware of CP5512: It’s different from PC Adapter and PC Adapter USB, CP5512 supports much more hardwares,such as Siemens S7-200/300/400PLC, PPI/MPI/PROFIBUS interface of touch panel, EM277,ET20 and other hardwares with PROFIBUS/MPI/PPI/FWL interface. It need PROFIBUS cable or MPI cable(Siemens part nr 6ES7 901-0BF00-0AA0) when CP5512 communicates with fieldbus devices.    Signal definition of CP5512 Interface:     Pin No.   Signal name   Description   Input / Output   1 NC Unused - 2 NC Unused - 3 B（RXD+/TXD+） RS485 Signal+ Input/Output 4 RTS_AS Handshake signal Input 5 Ground（0V） Signal Ground - 6 +5V 5V Power 50mA.max. Output 7 NC Unused - 8 A（RXD-/TXD-） RS485 Signal- Input/Output 9 RTS_PG Request Output Shell PE Shield -     More detailed of CP5512, please visit Siemens technical support site:   http://support.automation.siemens.com/CN/llisapi.dll?func=cslib.csinfo&lang=en&objid=6GK1551-2AA00&caller=view  

Introduction: Nowadays the laptops have eliminated the PCMCIA slot,but adopt the ExpressCard slot.So we especially develop the CP5512 EXPRESS for ExpressCard laptop.  ExpressCard CP5512,it’s suitable for Laptop Expresscard slot,is used to achieve PROFIBUS/MPI/PPI/FWLcommunication between PC and SIMATIC Net. Communication speed is 9.6Kbps--12Mbps.It can be also used for desktop computer after the conversion card. Not inlcude the MPI extension cable,for MPI cable,please click this link to get: MPI Cable The function of our CP5512 EXPRESS is the totally same as Siemens original CP5512 except they use on different laptop interfaces.It’s the isolated PROFIBUS/MPI/PPI/FWL communication card specially for laptop, use iCoupler Magnetic Coupling isolators to replace the optocoupler,with small  dimension, wide temperature range,and have anti-lightning and surging protective circuit and resumption of Overcurrent protection circuit on the RS485 interface, all use industrial IC in order to apply to wider temperature range, is used to achieve PROFIBUS/MPI/PPI/FWL communication connection between laptop and SIMATIC. CP5512 EXPRESS also can be used on PCI-E slot of desktop computer after the PCI-E to ExpressCard converter, the function is same as Siemens CP5611,CP5621. CP5512 EXPRESS support hot plug and plug and play. Perfect isolation circuit and interface protective circuit make you at ease to use it. Communication service:                                                                PROFIBUS-DP master station class 1 and 2 PROFIBUS-DP slave and SOFTNET-DP slave MPI/PPI/FWL communication S7 communication with SOFTNET-S7 S5-compatible communication (SEND/RECEIVE based on the FDL interface) with SOFTNET-D or SOFTNET-S7 CP5512 EXPRESS is suitable for the following version or above version softwares:                         STEP7  V5.2 SOFTNET-S7  V6.1 SOFTNET-DP, SOFTNET-DP slave from V6.1 STEP 7-Micro/WIN from V3.2 SP4 ProTool®, ProTool/Pro® V6.0 SP2 NCM PC from V5.2 SIMATIC PDM V5.2 SP1 Technical Specification:                                                                            Transmission rate: 9.6Kbps～12Mbps,the corresponding largest communication distance accord with PROFIBUS standard. Interface:connect PROFIBUS/MPI/PPI,isolated 9 pin Sub-D connector. Isolated voltage:1000VDC Interface protection:have anti-lightning and surging protection(Ipp=100A 10/700us,4KV) on the RS485 interface.ITU-TK20/21,VDE 0433 standard. ±15KV ESD protection. Overcurrent protection with  restoration function：RS485 port can withstand up to 60V voltage caused by continuous over-current. Standard working voltage:3.3 VDC power：1.0W  working temperature：-20～+75℃  size：adapter:length* width * height(mm)：123×68×30,cable length:  25CM weight：150g Support hardware of CP5512 EXPRESS:                                                            It’s different from PC Adapter and PC Adapter USB, CP5512 EXPRESS supports much more hardwares,such as Siemens S7-200/300/400PLC, PPI/MPI/PROFIBUS interface of touch panel, EM277,ET200 and other hardwares with PROFIBUS/MPI/PPI/FWL interface. It need PROFIBUS cable or MPI cable(Siemens part nr 6ES7 901-0BF00-0AA0) when CP5512 EXPRESS communicates with fieldbus devices.  Signal definition of CP5512 EXPRESS profibus Interface(DB9F):                                         Pin No. Signal name Description Input / Output 1 NC Unused - 2 NC Unused - 3 B（RXD+/TXD+） RS485 Signal+ Input/Output 4 RTS_AS Handshake signal Input 5 Ground（0V） Signal Ground - 6 +5V 5V power 50mA.max. output 7 NC Unused - 8 A（RXD-/TXD-） RS485 Signal- Input/Output 9 RTS_PG Request Output Shell PE Shield -     More detailed usage of CP5512 EXPRESS, please visit Siemens technical support site: http://support.automation.siemens.com/CN/llisapi.dll?func=cslib.csinfo&lang=en&objid=6GK1551-2AA00&caller=view    

CP5611-A2 communications cards which is Anti-lightning and anti-surge, corresponding to the Siemens 6 GK1 561-1AA01, photoelectric isolation, and applied to desktop computer's PCI slots, to achieve the PROFIBUS DP / MPI / PPI communications between PC or PG and the SIMATIC network, communication rate is 9.6 Kbps ~ 12Mbps. Not made by Siemens,OEM product Not including MPI extension cable for card communication,if you also need this,please also order it: MPI Cable Overview: CP5611-A2 communication card is optoelectronic isolated design for industrial applications.There is anti-lightning & anti-surging protection circuit and over-current protection on the RS485 port.The adoption of industrial chip applies to a wide temperature range. CP5611-A2 card is used to achieve the PROFIBUS DP / MPI / PPI communication between PC or PG and the SIMATIC network. Communication services: PROFIBUS-DP master grade 1 and 2 PROFIBUS-DP slave and SOFTNET-DP slave MPI/PPI communication PG/OP communication S7 communication with SOFTNET-S7 S5-compatible communication (SEND/RECEIVE based on the FDL interface) with SOFTNET-DP or SOFTNET-S7 CP5611-A2 applies to the following software: STEP7 V.52 and above SOFTNET-S7 SOFTNET-DP SOFTNET-DP slave COM PROFIVUS V3.3 and above STEP 7-Micro/WIN V3.1 and above ProTool, ProToo/Pro NCMPC Technical specifications: Transmission rate:9.6Kbps~12Mbps, corresponding maximum communication distance conforms to PROFIBUS standard Interface: PROFIBUS/MPI/PPI, isolated 9-pin Sub-D socket Isolation Voltage: 1000VDC RS485 port with anti-lightning and anti-surging protector, repeatability surge capacity: Ipp = 100A (10/700us, 4KV) Standard: ITU-TK20/21, VDE 0433. ± 15KV ESD (ESD) protection Over-current protection: RS485 interface can withstand up to 60V voltage caused by the sustained over-current PG/PC connection: PCI2.1 standard slot Standard voltage: +5 VDC Power: 2.0W Operating temperature: 0 ~ + 70 'C Size (width x high) (mm): 102 x 130 Weight: 100g  

Correspond to Omron CQM1-CIF02/01,RS232 PLC programming cable for OMRON CQM1,CPM1, CPM1A, CPM2A,C200HS,C200HX/HG/HE,SRM1 series,3 meters  

Mitsubishi FX series USB PLC programming interface conversion cable.USB/RS422 interface for Mitsubishi FX3U/FX2N/FX1N/FX0/FX0S/FX1S series PLC, 2.5 meters, with communication indicator, the largest communications range is up to 2Km. Summary: FX-USB-AW is the programming cable in which USB interface provided both the serial connection and RS422 signal conversion. Under the control of computer-driven driver, the programming cable makes it possible for the computer's USB interface to simulate the traditional serial (known as COM interface), thus various existing programming software such as communications software, monitoring software and other applications can be normally used. The working power supply of this cable is directly from the USB port, but not the PLC programming interface. The two-color LED on the converter box indicates data’s transceiving status. FX-USB-AW is applicable to the FX3U series PLC which has the MD8F radio socket of Mitsubishi, such as FX3U/FX2N/FX1N/FX0/FX0N/FX0S/FX1S, and it can substitute the FX-232AW module. The largest communications distance is two kilometers. Do choose the USB-SC09 programming cable, for A and all FX series Mitsubishi PLC (including the old products FX2/FX2C). FX-USB-AW principle and figure structure: FX-USB-AW programming cable simulate USB port as traditional serial port (usually COM3), which enables existing programming software(GX Developer) to communicate through simulated traditional port and PLC devices. Features and technological index: ● Support FX-USB-AW operating system: Windows2000/XP (WinNT4/95/98/Me/DOS not included ) ● Support FX-USB-AW programming software version: FXGP / WIN V1.0, GPP V4.0, GX Developer V7.0 and above.● Fully compatible with USB V1.1 norms and USB CDC V1.1 ● USB-bus powered, with current consumption of 50 mA ● Baud rate: 300 bps ~ 1Mbps automatically adapt to the standard baud rate ● Support UART data format: data bits: 7-8; stop bit: 1, 2; check-bit: odd / even / no parity ● Support long-distance communications, the largest communications is two kilometers (9600 bps) ● Each PC only supports one USB cable programming ● Working temperature: -20 ~ +75 ℃ ● Cable length: 2.5m; Color: black System requirement Please make sure your PC is IBM PC compatible and has the following system requirements before using the USB programming cable. ● Intel is compatible with 586DX4-100MHz CPU or higher ● A standard USB port (4-pin A plug) ● Operating system is Windows2000 or Windows XP       Setting of GX Developer After completing Driver installation, the corresponding COM port for the FX-USB-AW programming cable will be displayed in the “Device Manager” of Window. The next step is just to choose this COM port in the programming software and other application software and keep other communication parameters as in the Default settings. And the following steps are exactly the same as the traditional programming cables with RS232 interfaces. Note: DB25M plugs and MD8M plugs of the RS422 interface can not be used at the same time.  Open the main windows form(GX Developer)， choose “Online” menu then click “Transfer Setup…” and will appear “Transfer Setup” window. Click “Serial” button of the PC side I/F, and choice the COM X interface as it in the Device Manager.     About Long Distance Communication For FX-USB-AW,The largest communication distance is up to two kilometers (9600 bps).The user must follow the self-made plan to extend cable. Transmission Line should be 0.22mm or more, twisted pair wire. When the distance is over 2,000 m,RS422 repeater could be installed to extend the distance. Please Note: USB interface cable cannot be extended.   Due to internal resistance have been installed in FX-USB-AW and the PLC, no external terminal resistance is needed. Usage: USB device drivers should be installed before using FX-USB-AW programming cable, which are available on the CD-ROM sold together with the cable. And for the specific installation steps, please refer to the instruction files on the CD-ROM drivers, and details are not necessarily listed here. After completing Driver installation, the corresponding COM port for the FX-USB-AW programming cable will be displayed in the “Device Manager” of Window. The step next is just to choose this COM port in the programming software and other application software and keep other communication parameters as in the Default settings. And the following steps are exactly the same as in the traditional programming cables with RS232 interfaces. Long-distance communications: the largest communications range between the FX-USB-AW programming cable and the PLC is up to two kilometers (9600 bps)。The user must follow the self-made plans to extend cable. Transmission Line should be 0.22mm2 or more, twisted pair wire. When the distance is over 2,000 m , RS422 repeater could be installed to extend the distance. Please Note: USB interface cable cannot be extended.  

RS232 optoelectronic isolated programming cable for Siemens LOGO!,3 meters,can replace Siemens 6ED1 057-1AA00-0BA0 The quality is guaranteed.It's tested before shippment.Not made by Siemens,OEM product as the replacement.

This adapter is compatible with Siemens PC Adapter and HMI adapter,fully support  RS232 port of PC and HMI to PROFIBUS/MPI communication, use the Siemens special protocol processing chip,it can be used for Siemens S7-300/400 series PLC and other equipments with PROFIBUS/MPI interface. RS232-RS485-power supply are all optical isolated, especially suitable for the strong interference and communication interface easily damaged industrial scene. PC Adapter CN is a high-tech adapter compatible with Siemens PC Adapter and HMI Adapter,fully support RS232 serial port of PC and HMI to PROFIBUS/MPI communication, adopt the Siemens protocol processor chip,no functional defects. PC Adapter CN is the opto-isolated adapter for industrial design.It has the surge protection and anti-lightning protection circuit on the RS232 interface and RS485 interface, support hot plug, is suitable for Siemens S7-300/400 series PLC and other equipments with PROFIBUS/MPI interface. In particular, it applies to the strong interfere industrial situations and the safeguard in the circuit guarantees the safely running of the system. PC Adapter CN can communicate between S7-300/400PLC and RS232 interface of third party HMI,can replace the Siemens HMI Adapter. The low version PC/MPI+ didn’t adopt the Siemens protocol processor chip,but adopt the MCU and use the software to achieve the profibus protocol,the protocol is not perfect and has the defect,only support MPI communication,not support profibus communication,can only connect few HMI and have the defect. When there are many nodes or third-party device in the network,it can’t identify every node. At the same time, it may have the risk that PC/MPI+ can’t be used after the PLC internal program is upgraded in the future. Main Technical Specifications:                                                                           ● RS232 interface can connect PC or HMI etc third party devices,baud rate 9.6Kbps～115.2Kbps automatically adjust. ● Support PROFIBUS and MPI communication, auto bus protocol test,largest baud rate 1.5Mbps. ● Power supply from PLC port,24VDC, Power Consumption 2W,with over current and surge protection. ● Power-RS485-RS232 all isolated ● Opto-isolated voltage 1000VDC. ● RS232 interface has the anti-surging protection ● RS485 interface has the anti-lightning and surging protector, Repeatability surge capacity: Ipp=100A(10/700us，4KV),meet the standard ITU-TK20/21、VDE 0433. ±15KV ESD protection. ● Need additional 24VDC power for the long distance communication, the largest cable length meets the profibus standard. ● With the power indicator, data sending indicator, data receiving indicator Can install the adapter on the S7-300/400PLC rail or 35MM standard rail. ● Shape Size: 123mm×68mm×30mm(Length*Width*Height),with the mounting bracket ● Working Temperature: -20～+75℃  

New OEM Siemens S7-200 PC/PPI+ PLC Programmer Cable2 If you need non- isolated cable,pls choose PC/PPI,you can click the following website for PC/PPI:PC-PPI, The quality is guaranteed.It's tested before shippment. optoelectronic isolated PC/PPI cable,support 10 bit and 11 bit modem communication,with communication indicator,automatically adjust the baud rate from 0 to 115.2Kbps,the largest communication distance of up to 2 kilometers.Not support multi-master station communication.,5M. Specifications: The OEM Siemens S7-200 PC-PPI+ Programming cable supports full range of Siemens S7-200 PLC programming. It is 100% good replacement for the expensive Simens cable.. It's tested and proven on S7-212, S7-211, S7-214, S7-224, S7-224XP and it works as a standard Simens serial PC/PPI+ port. We also provide other Compatible Accessories for Siemens PLC series, please contact us to buy it! Accessories of Replacements Orignal Siemens Model Profibus BUS Connector（90 without Program interface） 6ES7972-0BA12-0XA0 Profibus BUS Connector（90 with Program interface） 6ES7972-0BB12-0XA0 Profibus BUS Connector（35 without Program interface） 6ES7972-0BA41-0XA0 Profibus BUS Connector（35 with Program interface） 6ES7972-0BB41-0XA0 Profibus BUS Connector 6ES7 972-0BA50-0XA0 Profibus BUS Connector 6ES7 972-0BB50-0XA0 Profibus BUS Connector 6ES7 972-0BA52-0XA0 Profibus BUS Connector 6GK1500-0FC10 Profibus BUS Connector 6ES7 972-0BB52-0XA0 Profibus BUS Connector 6GK1 500-0EA02 Profibus BUS Connector 6GK1 500-0FC00 Profibus BUS Cable 6XV1 830-0EH10 Profibus BUS Cable 6XV1830-3EH10 Profibus BUS Cable 6XV1840-2AH10 20-Pin front Connector 6ES7392-1AJ00-0AA0 40-Pin front Connector 6ES7392-1AM00-0AA0 CP5611 Card 6GK1561-1AA00 CP5611 Card 6GK1561-1AA01 PLC Li-on Battery 6ES7291-8BA20-OXAO PS307 Power supply 5A 6ES7307-1EA00-0AA0 PS307 Power supply 10A 6ES7307-1KA01-0AA0 PS307 Power supply 10A 6ES7307-1KA02-0AA0 DIN Track（830mm） 6ES7390-1AJ30-0AA0 DIN Track（530mm） 6ES7390-1AF30-0AA0 DIN Track（480mm） 6ES7390-1AE80-0AA0 Hot-Plug Track（530mm） 6ES7390-1GF30-0AA0 The PC/PPI+ programming cable is the transformation electric cable from RS232 to the PPI connection (RS485), and it is suitable for Simens S7-200 series PLC and the TP170 touchscreen programming, the correspondence and the monitoring. It also supports the PPI agreement and the free mouth communication protocol, and can use MODEM (modem) through the telephone line to make a long-distance correspondence. Since the cable is isolated with the electro-optical and built-in anti-static, surge and other transient over-voltage protection circuit, it solves the problem that the communication I always burned easily well. And it is especially suitable for the long-term monitoring communications which are under the industrial site with a poor environment. Main technical parameters： ★ Isolation voltage: 1000VDC(The maximum to 3000 VDC, orders required statement)★ According to a transient voltage suppression. The RS485 port can withstand the power of up to 500 W transient over-voltage and lightning impact，the RS232 port and power circuit are equipped with surge protection to protect the circuit. The whole product can be arbitrarily charged plug.★ Baud rate：0～115.2kbps Adaptive(products available for sale since January 2008 )★ The longest communication distance：2 km(Baud rate:9600bps per hour)，1km(Baud rate:115.2Kbps per hour)★ With a power indicator light and the data received and sent indicator light★ Temperature:-40～85'C(products available for sale since January 2008)★ Dimension：103×50×26，The total length of cable is 5m. The product structure： PPI-RS485 plug PC-RS232 plug Pin Signal explanation Pin Signal explanation 2 24V Power source negative（RS485 Logical place） 2 Receive data RD（Output from PC/PPI） 3 RS485 signal B（RxD/TxD+） 3 Send data SD（Send to PC/PPI） 7 24V Power source positive 4 Data terminal ready DTR 8 RS485 signal A（RxD/TxD-） 5 Ground（RS232 Logical place） 9 Agreement choice 7 Require to send RTS Signals of PC-RS232 plugs and PPI-RS485 plugs The use of products： 1, PLC and computer connections for the PPI or free Communication, programming：Insert the PC / PPI + cable’s RS485 plug into the programming mouth of S7-200PLC and the RS232 plug into the computer’s RS232 port. Chose the corresponding number of the COM port. Switch the 10bit, 11bit selection switch to 11 bit. The baud rate of the PC/PPI+ cable is adaptive from 0 to 115.2kpbs. There is no need to set that.2, The long-distance communications between PLC and computer：When having long-distance communications, the PC / PPI + requires additional external power and we should parallel 120Ωi end resistance n between the 3, 8 of RS485 plugs to eliminate signal reflection, as shown below:3, long-distance communications between the PLC and computer via telephone lines:You have to make a cross-adapter by yourself when you get the PC/PPI+’s RS232 port and the MODEM connected. Switch to the corresponding location according to the MODEM that it is 10 or 11.10 bits MODEM refers: 1 outset bit, 8 data bits, no parity bit, and 1 stop bit(or 7 data bits,1 parity bit).This kind of MODEM is comparative common on the market.11 bits MODEM refers: 1 outset bit, 8 data bits, 1 parity bit (Occasionally bit check), and 1 stop bit . The quality is guaranteed.It's tested before shippment.Not made by Siemens,OEM product as the replacement. Package Includes: OEM Siemens PC/PPI+PLC Programmer Cable X 1

RS232/RS232 interface,cable for Mitsubishi Q series PLC,3 meters.Not isolated,so it doesn't support hot plug,if need isolated cable,pls choose QC30R2+,you can click it :QC30R2+

Go on long-distance communication for FX series(FX2/FX2n/FX0/FX0n..) with modem connecting telephone wire,the other function is the same as SC-09.

USB/RS422 interface,adapter for Mitsubishi FX2N/FX1N/FX0/FX0S/FX1S/FX3U series PLC,2.5 meters,with communication indicator, the largest communication distance of up to 2 kilometers. Compatible with FX-USB-AW. Summary: USB-SC09-FX is the programming cable in which USB interface provided both the serial connection and RS232 signal conversion. Under the control of computer-driven driver, the programming cable makes it possible for the computer's USB interface to simulate the traditional serial (known as COM interface), thus various existing programming software such as communications software, monitoring software and other applications can be normally used. The working power supply of this cable is directly from the USB port, but not the PLC programming interface. The two-color LED on the converter box indicates data’s transceiving status. USB-SC09-FX is applicable to the FX series PLC which has the MD8F radio socket of Mitsubishi, such as FX2N/FX1N/FX0/FX0N/FX0S/FX1S/FX3U, and it can substitute the FX-232AW module. The largest communications distance is two kilometers. Do choose the USB-SC09 programming cable, for all FX series Mitsubishi PLC (including the old products FX2/FX2C). Outline configuration: Features and technological index: ● Support USB-SC09-FX programming software version: FXGP / WIN V1.0, GPP V4.0, GX Developer V7.0 and above. ● Fully compatible with USB V1.1 norms and USB CDC V1.1 ● USB-bus powered, with current consumption of 50 mA ● Baud rate: 300 bps ~ 1Mbps automatically adapt to the standard baud rate ● Support UART data format: data bits: 7-8; stop bit: 1, 2; check-bit: odd / even / no parity ● Support long-distance communications, the largest communications is two kilometers (9600 bps) ● Each PC only supports one USB cable programming ● Working temperature: -20 ~ +75 'C ● Cable length: 2.5m; Color: black Usage: USB device drivers should be installed before using USB-SC09-FX programming cable. After completing Driver installation, the corresponding COM port for the USB-SC09-FX programming cable will be displayed in the “Device Manager” of Window. The step next is just to choose this COM port in the programming software and other application software and keep other communication parameters as in the Default settings. And the following steps are exactly the same as in the traditional programming cables with RS232 interfaces.     Long-distance communications: the largest communications range between the USB-SC09-FXprogramming cable and the PLC is up to two kilometers (9600 bps).The user must follow the self-made plans to extend cable. Transmission Line should be 0.22mm2 or more, twisted pair wire. When the distance is over 2,000 m , RS422 repeater (model: E485GA)could be installed to extend the distance. Please Note: USB interface cable cannot be extended.      Due to internal resistance have been installed in USB-SC09-FX and the PLC, no external terminal resistance is needed. The quality is guaranteed.It's tested before shippment.Not made by Mitsubishi,OEM product as the replacement